Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateCarrier Furnace Repair in Henderson: What to Know First
Carrier furnace repair in Henderson typically runs $150 – $700 depending on the part that failed, and our techs carry the most common Carrier components on the truck so most jobs are finished same-day. We’re an independent Carrier service provider – not a Carrier dealer – which means we answer only to you, not to a manufacturer’s sales quota. If you own a Carrier Infinity, Performance, or Comfort series furnace and it’s acting up, call (775) 593-7060 and you’ll get a real person, a straight answer, and a written price before anything gets touched.
How Carrier Products Fail – and How We Fix Them
Carrier builds a solid furnace, but every brand has its patterns. Here’s what we actually see on service calls across Henderson:
- Infinity series (59MN7, 59TN6) – pressure switch faults on windy days. The modulating gas valve and variable-speed inducer are smart pieces of engineering, but the pressure switch tubing is thin and prone to collecting condensation or dust. A fault code 31 or 32 doesn’t always mean the switch is bad; often the tube just needs clearing and reseating. We check the whole circuit before quoting a part.
- Performance series (59TP6) – hot surface ignitor failure. This is the single most common Carrier repair we do in Henderson. The ignitor is a ceramic element that glows red-hot to light the gas. They get brittle with age and cycling, typically failing around year 10 – 14. The symptom is usually a furnace that runs the inducer motor but never lights. It’s a $150 – $350 job depending on whether we’re replacing the ignitor alone or the ignitor and flame sensor together.
- Comfort series (58STA, 58STX) – flame sensor carbon buildup. These single-stage workhorses are common in older Henderson subdivisions. The flame sensor sits in the burner flame and develops a carbon coating that blocks the microamp signal. If your furnace lights, runs for three to five seconds, then shuts off and retries, that’s a dirty flame sensor about 80% of the time. We clean it as part of any tune-up and replace it if cleaning doesn’t hold.
- All Carrier 90%+ efficiency models – condensate drain clogs. High-efficiency furnaces make water as a byproduct of combustion. Henderson’s hard water leaves mineral deposits that build up in the drain trap and line. If your Carrier furnace shuts down with a code 33 or you see water staining around the base, the trap likely needs cleaning. This is a $150 – $200 fix most of the time, and it’s one we’d rather catch in a tune-up than at 2 a.m.
- Blower motor issues across all lines – especially the ECM motors in Infinity and Performance. When the module on an ECM blower motor fails, the furnace may run but push weak airflow, or not run the blower at all. Newer Carrier ECM motors are expensive; a full replacement can hit that $700 top end. Before we recommend one, we check the module separately because sometimes you only need the module, not the whole motor assembly.
Styles & brands we work with
Our Carrier Furnace Repair Process
Here’s how a Carrier repair call goes with Dalton Heating & Air Henderson, from phone call to cleanup:
- 1
You call and talk to a person. Not a voicemail tree, not a callback queue. We answer 24/7 and you’ll describe the symptom in your own words.
- 2
We arrive in the window we gave you. Every tech is background-checked and uniformed. Marco Benitez has drilled the crew on The Garrison Code: show up when you said you would, and if you’re going to be late, call before you’re late.
- 3
We diagnose in front of you. We test the ignitor, flame sensor, pressure switch, gas valve, and control board as needed. We show you what’s failed and explain it in plain terms – no mystery, no upsell theater.
- 4
We put the price in writing before we start. That’s non-negotiable. The number includes parts, labor, and the full year of warranty coverage. If the job requires an OEM Carrier part, the price reflects that; if a quality aftermarket part makes better sense for an older system, we’ll tell you why and let you decide.
- 5
We fix it and test it. The repair isn’t done until we’ve cycled the furnace multiple times, confirmed the flame sensor is reading clean, and checked gas pressure and temperature rise.
- 6
We leave the site clean and hand you a written guarantee. Every repair carries a 365-day written guarantee. If the work fails within that year, we return at no charge. That’s the Done Right Promise, and it’s in writing.
What Carrier Furnace Repair Costs in Henderson
Most Carrier furnace repairs in Henderson land between $150 and $700. The lower end covers jobs like flame sensor cleaning, pressure switch tubing, drain trap clearing, and capacitor replacement. The mid-range – $250 to $450 – is where you’ll find hot surface ignitor replacement, gas valve repair on single-stage units, and inducer motor replacements. The $450 to $700 range covers ECM blower motors on Infinity and Performance models, control board replacement, and heat exchanger repair on select units. What moves the price: whether the part is OEM or aftermarket, the age and model of your furnace, and whether we’re fixing one issue or uncovering a second one during testing. Call (775) 593-7060 for a free estimate – the price you hear is the price in writing before we begin.
See the difference
Before
After
Before
After
Before
AfterWhy Henderson Homeowners Call Dalton Heating & Air Henderson for Carrier Work
Henderson has plenty of HVAC companies that will “take a look” at your Carrier. Few will hand you a written price before touching a screwdriver, guarantee the repair in writing for a full year, and send a tech who was factory-trained on nine major brands. That’s the part that matters with Carrier: their modulating furnaces and communicating thermostats require real diagnostics, not guesswork. Our techs work on Carrier weekly, but they also know Trane and Lennox inside and out – which matters if your heat pump or air handler was mixed and matched by a previous owner. The Garrison Standard has been our operating rule since 2003, and it’s simple: arrive inside the window, price it in writing, do the job by the book, leave the site clean, stand behind the work for a year. Marco likes to put it another way: “If the price surprises you, something went wrong before I even opened my toolbox.”
FAQs
Yes. If your Carrier furnace is still under the manufacturer’s parts warranty, we can perform the diagnosis and repair, and you’ll pay only for labor while we document everything needed for any warranty claim. As an independent provider we don’t file the warranty paperwork with Carrier on your behalf, but we give you the documentation and part numbers to do it cleanly, and we’ll help you understand what’s covered before any money changes hands.
Most of the time, yes. Our trucks are stocked with common Carrier parts – ignitors, flame sensors, pressure switches, capacitors, drain components – so a high percentage of calls are finished in one visit. For less common parts like a specific Infinity control board or ECM module, we can typically source it from local Henderson supply houses the same day or first thing the next morning. Call (775) 593-7060 and tell us the symptom; we’ll tell you what to expect.
A good rule: if the repair costs less than a third of a replacement and your furnace is under 15 years old, repair usually makes sense. If you’re looking at a $700 ECM motor on an 18-year-old Comfort series, that’s when we’ll honestly talk about whether your money is better spent toward a new system. We don’t earn a commission on replacement recommendations, and we’ll show you the numbers either way.
Under U.S. consumer law, a manufacturer cannot void your warranty solely because an independent company used non-OEM parts. That said, for newer furnaces still under warranty, we generally recommend genuine Carrier OEM components for compatibility and longevity. For older units where the warranty has expired, we’ll discuss whether a quality aftermarket part gives you the same reliability at a better price.
Once a year, ideally in the fall before the first cold snap. Henderson winters are mild compared to the Midwest, but furnaces here sit idle for months and then get called into service – which is exactly when ignitors crack, drain traps dry out, and flames sensors corrode. A $80 – $200 tune-up catches most of those failures before they become a no-heat night.
Call Dalton Heating & Air Henderson for Carrier Furnace Repair
If your Carrier furnace is throwing a code, short-cycling, or just not lighting, don’t wait until the next cold front to find out the ignitor is dead. Call (775) 593-7060 and you’ll get a live person 24/7, a technician who arrives in the window we give you, a written price before the work starts, and a 365-day written guarantee when it’s done. That’s how we’ve operated since 2003, and that’s exactly how a repair should work.
Written by Marco Benitez, Owner, Dalton Heating & Air Henderson at Dalton Heating & Air Henderson, serving Henderson and nearby areas.